Starter and Twist Drill |
---|
|

Started | TEC-2 |
---|---|
ZD03.001 | ZD03.002 |
Countersink Drill |
---|
|

2.8/3.5 | 3.6/4.3 | 4.3/5 |
---|---|---|
ZD03.001 | ZD03.002 | ZD03.008 |
Direction Indicator |
---|
|

2.8/3.5 | 3.6/4.3 | 4.3/5 |
---|---|---|
ZD28.002 | ZD28.003 | ZD28.004 |
Implant Driver Contra-Angle |
---|
|

ZD05.007 |
Implant Driver Ratchet |
---|
|

Short | Long |
---|---|
ZD05.005 | ZD05.006 |
Height Measurer |
---|
|

ZD28.001 |
Drill Extension |
---|
|

ZD03.020 |
Implant Driver |
---|
|

ZD04.007 |
Hand Screwdriver 0.9 M |
---|
|

Medium 25 mm | Long 38 mm |
---|---|
ZD04.005 | ZD04.012 |
Hand Screwdriver 1.2 M |
---|
|

Short 20 mm | Medium 25 mm |
---|---|
ZD04.002 | ZD04.003 |
Screwdrivers |
---|
|

0.048/1.2 Short | 0.063/1.6 Short | 0.035/0.9 |
---|---|---|
ZD05.008 | ZD05.009 | ZD05.004 |
0.048/1.2 | 0.063/1.6 | Prosthetic Abutment Driver |
ZD05.001 | ZD05.002 | ZD05.003 |
0.048/1.2 Long | Manual |
---|---|
ZD05.010 | ZD04.001 |
Ratchet Screwdriver Slot |
---|
|

ZD05.014 |
Driver for Bone Tap Contra-Angle |
---|
|

ZD05.012 |
Driver for Bone Tap Ratchet |
---|
|

Short | ZD05.011 |
Long | ZD05.013 |
Hand Implant Driver Contra-Angle |
---|
|

ZD04.011 |
Drivers for Contra Angle 0.9 mm |
---|
|

Medium | ZD05.015 |
Short | ZD05.016 |
Bone Profile Drill |
---|
|

ZD03.033 |
Drill Positioner 17° ve 30° |
---|
|

17° | ZD28.005 |
30° | ZD28.006 |
Trephine Bur |
---|
|

Ø 4.3 | Ø 5.0 |
---|---|
ZD03.031 | ZD03.030 |
Implant Removal |
---|
|

ZD30.001 |
X Ray Positioner |
---|
|

Ø 3.5 | Ø 4.3 | Ø 5.0 |
---|---|---|
ZD29.001 | ZD29.002 | ZD29.003 |
Concave Osteotome |
---|
|

1.8 mm | 2.5 mm | 3.0 mm |
---|---|---|
ZD10.002 | ZD10.003 | ZD10.004 |
3.5 mm | 4.0 mm | 4.5 mm |
ZD10.005 | ZD10.006 | ZD10.007 |
Bone Scraper |
---|
|

ZD27.001 |
Ratchet |
---|
|

ZD04.006 |
Operation Instructions

The Zinedent ratchet was designed to allow the necessary torque to be applied and simultaneous verification of that torque with the same instrument.

(never the Ratchet body) until the value marked on the LATERAL SCALE


The ratchet function works in both directions, by simply pulling and turning the driver’s pin 180°. However, the torque measurements work only clockwise.
WARNING: When inverting the torque direction, the gear may come loose from the driver body and fall. Therefore, this inversion should only be done with the driver connected to a part or outside the patient’s mouth.
WARNING: When inverting the torque direction, the gear may come loose from the driver body and fall. Therefore, this inversion should only be done with the driver connected to a part or outside the patient’s mouth.

The Zinedent ratchet comes with pre-calibrated torques: 10, 20, 32, 45 and 60 N.cm.